Login or Register for FREE!
Subelement L09

Transmitters.

Section L09

The output tuning controls on a transmitter power amplifier with an adjustable PI network:

  • allow switching to different antennas
  • reduce the possibility of cross-modulation in adjunct receivers
  • are involved with frequency multiplication in the previous stage
  • Correct Answer
    allow efficient transfer of power to the antenna

Tube power amplifiers always include a matching network to match the high impedance of the tube to the antenna system impedance. As always, impedance match is all about maximum power transfer.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

The purpose of using a centre-tap return connection on the secondary of transmitting tube's filament transformer is to:

  • obtain optimum power output
  • Correct Answer
    prevent modulation of the emitted wave by the alternating current filament supply
  • reduce the possibility of harmonic emissions
  • keep the output voltage constant with a varying load

When the cathode is simply the filament (a "directly-heated cathode"), the voltage drop across the filament (e.g., 6.3 volts AC) is in series with the cathode DC reference voltage: as an example, while one side of the filament might be at a certain DC voltage, the other extremity is at some other value, a value influenced by the AC voltage impressed on the filament. Electron flow is affected by an AC variation, hum results.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, the input signal is applied to:

  • Correct Answer
    the cathode
  • the plate
  • the control grid
  • the filament leads

A grounded-grid amplifier runs with the grid at ground potential. The cathode is above RF ground and serves as the input. A DC bias is applied to the cathode via an RF choke. Positive voltage (B+) is supplied to the plate via an RF choke. The plate is the output, a blocking capacitor passes the RF out to the matching network. A transformer provides AC filament voltage. The heater (in an indirectly-heated cathode tube) is bypassed to ground so radiofrequency does not stray out on the filament supply lines. [ If a tube is directly-heated (no separate cathode), filament voltage is brought through a filament choke. The side of the choke connected to the transformer is bypassed to ground with two capacitors. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, the plate is connected to the pi-network through a:

  • electrolytic capacitor
  • Correct Answer
    blocking capacitor
  • by-pass capacitor
  • tuning capacitor

A grounded-grid amplifier runs with the grid at ground potential. The cathode is above RF ground and serves as the input. A DC bias is applied to the cathode via an RF choke. Positive voltage (B+) is supplied to the plate via an RF choke. The plate is the output, a blocking capacitor passes the RF out to the matching network. A transformer provides AC filament voltage. The heater (in an indirectly-heated cathode tube) is bypassed to ground so radiofrequency does not stray out on the filament supply lines. [ If a tube is directly-heated (no separate cathode), filament voltage is brought through a filament choke. The side of the choke connected to the transformer is bypassed to ground with two capacitors. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, the plate is connected to a radio frequency choke. The other end of the radio frequency choke connects to the:

  • ground
  • B- (bias)
  • Correct Answer
    B+ (high voltage)
  • filament voltage

A grounded-grid amplifier runs with the grid at ground potential. The cathode is above RF ground and serves as the input. A DC bias is applied to the cathode via an RF choke. Positive voltage (B+) is supplied to the plate via an RF choke. The plate is the output, a blocking capacitor passes the RF out to the matching network. A transformer provides AC filament voltage. The heater (in an indirectly-heated cathode tube) is bypassed to ground so radiofrequency does not stray out on the filament supply lines. [ If a tube is directly-heated (no separate cathode), filament voltage is brought through a filament choke. The side of the choke connected to the transformer is bypassed to ground with two capacitors. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, the cathode is connected to a radio frequency choke. The other end of the radio frequency choke connects to the:

  • Correct Answer
    B- (bias)
  • ground
  • filament voltage
  • B+ (high voltage)

A grounded-grid amplifier runs with the grid at ground potential. The cathode is above RF ground and serves as the input. A DC bias is applied to the cathode via an RF choke. Positive voltage (B+) is supplied to the plate via an RF choke. The plate is the output, a blocking capacitor passes the RF out to the matching network. A transformer provides AC filament voltage. The heater (in an indirectly-heated cathode tube) is bypassed to ground so radiofrequency does not stray out on the filament supply lines. [ If a tube is directly-heated (no separate cathode), filament voltage is brought through a filament choke. The side of the choke connected to the transformer is bypassed to ground with two capacitors. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, the secondary winding of a transformer is connected directly to the vacuum tube. This transformer provides:

  • Screen voltage
  • Correct Answer
    filament voltage
  • B- (bias)
  • B+ (high voltage)

A grounded-grid amplifier runs with the grid at ground potential. The cathode is above RF ground and serves as the input. A DC bias is applied to the cathode via an RF choke. Positive voltage (B+) is supplied to the plate via an RF choke. The plate is the output, a blocking capacitor passes the RF out to the matching network. A transformer provides AC filament voltage. The heater (in an indirectly-heated cathode tube) is bypassed to ground so radiofrequency does not stray out on the filament supply lines. [ If a tube is directly-heated (no separate cathode), filament voltage is brought through a filament choke. The side of the choke connected to the transformer is bypassed to ground with two capacitors. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, what would be the approximate B+ voltage required for an output of 400 watts at 400 mA with approximately 50 percent efficiency?

  • 500 volts
  • 3000 volts
  • 1000 volts
  • Correct Answer
    2000 volts

400 watts out at 50% efficiency supposes that 800 watts DC are needed. Power is voltage times current ; thus, voltage is power divided by current ; 800 watts divided by 0.4 ampere = 2000 volts.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a grounded grid amplifier using a triode vacuum tube, each side of the filament is connected to a capacitor whose other end is connected to ground. These are:

  • electrolytic capacitors
  • blocking capacitors
  • Correct Answer
    by-pass capacitors
  • tuning capacitors

A grounded-grid amplifier runs with the grid at ground potential. The cathode is above RF ground and serves as the input. A DC bias is applied to the cathode via an RF choke. Positive voltage (B+) is supplied to the plate via an RF choke. The plate is the output, a blocking capacitor passes the RF out to the matching network. A transformer provides AC filament voltage. The heater (in an indirectly-heated cathode tube) is bypassed to ground so radiofrequency does not stray out on the filament supply lines. [ If a tube is directly-heated (no separate cathode), filament voltage is brought through a filament choke. The side of the choke connected to the transformer is bypassed to ground with two capacitors. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

After you have opened a VHF power amplifier to make internal tuning adjustments, what should you do before you turn the amplifier on?

  • Remove all amplifier shielding to ensure maximum cooling
  • Correct Answer
    Be certain all amplifier shielding is fastened in place
  • Make sure that the power interlock switch is bypassed so you can test the amplifier
  • Be certain no antenna is attached so that you will not cause any interference

Running a VHF or UHF power amplifier without shielding presents a safety risk in terms of RF exposure.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Harmonics produced in an early stage of a transmitter may be reduced in a later stage by:

  • greater input to the final stage
  • transistors instead of tubes
  • Correct Answer
    tuned circuit coupling between stages
  • larger value coupling capacitors

Key words: STAGES. Resonant circuits in the coupling between stages help convey only the operating frequency. Larger coupling capacitors would pass the harmonics more readily.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a simple 2 stage CW transmitter circuit, the oscillator stage and the class C amplifier stage are inductively coupled by a RF transformer. Another role of the RF transformer is to:

  • provide the necessary feedback for oscillation
  • act as part of a balanced mixer
  • Correct Answer
    be part of a tuned circuit
  • act as part of a pi filter

A simple two-stage CW transmitter comprises an oscillator and a Class-C power amplifier. A transformer at the output of the oscillator serves the dual purpose of tuned circuit and coupling to the next stage. The DC supply to the final amplifier is bypassed to ground with a capacitor and decoupled through an RF choke so RF is kept out of the supply.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a simple 2 stage CW transmitter, current to the collector of the transistor in the class C amplifier stage flows through a radio frequency choke (RFC) and a tapped inductor. The RFC, on the tapped inductor side, is also connected to grounded capacitors. The purpose of the RFC and capacitors is to:

  • Correct Answer
    form a low-pass filter
  • provide negative feedback
  • form a key-click filter
  • form a RF-tuned circuit

A simple two-stage CW transmitter comprises an oscillator and a Class-C power amplifier. A transformer at the output of the oscillator serves the dual purpose of tuned circuit and coupling to the next stage. The DC supply to the final amplifier is bypassed to ground with a capacitor and decoupled through an RF choke so RF is kept out of the supply.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In a simple 2 stage CW transmitter, the transistor in the second stage would act as:

  • the master oscillator
  • an audio oscillator
  • Correct Answer
    a power amplifier
  • a frequency multiplier

A simple two-stage CW transmitter comprises an oscillator and a Class-C power amplifier. A transformer at the output of the oscillator serves the dual purpose of tuned circuit and coupling to the next stage. The DC supply to the final amplifier is bypassed to ground with a capacitor and decoupled through an RF choke so RF is kept out of the supply.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

An advantage of keying the buffer stage in a transmitter is that:

  • Correct Answer
    changes in oscillator frequency are less likely
  • key clicks are eliminated
  • the radiated bandwidth is restricted
  • high RF voltages are not present

Keying a subsequent stage provides the oscillator with a fairly constant load (isolation) and allows it to run continuously for better stability.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

As a power amplifier is tuned, what reading on its grid current meter indicates the best neutralization?

  • Minimum grid current
  • Maximum grid current
  • A maximum change in grid current as the output circuit is changed
  • Correct Answer
    A minimum change in grid current as the output circuit is changed

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What does a neutralizing circuit do in an RF amplifier?

  • It eliminates AC hum from the power supply
  • It reduces incidental grid modulation
  • It controls differential gain
  • Correct Answer
    It cancels the effects of positive feedback

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the reason for neutralizing the final amplifier stage of a transmitter?

  • To cut off the final amplifier during standby periods
  • To keep the carrier on frequency
  • Correct Answer
    To eliminate parasitic oscillations
  • To limit the modulation index

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Parasitic oscillations are usually generated due to:

  • a mismatch between power amplifier and transmission line
  • Correct Answer
    accidental resonant frequencies in the power amplifier
  • harmonics from some earlier multiplier stage
  • excessive drive or excitation to the power amplifier

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Parasitic oscillations would tend to occur mostly in:

  • Correct Answer
    RF power output stages
  • high gain audio output stages
  • high voltage rectifiers
  • mixer stages

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Why is neutralization necessary for some vacuum-tube amplifiers?

  • To reduce grid-to-cathode leakage
  • To cancel AC hum from the filament transformer
  • To reduce the limits of loaded Q
  • Correct Answer
    To cancel oscillation caused by the effects of interelectrode capacitance

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Parasitic oscillations in an RF power amplifier may be caused by:

  • excessive harmonic production
  • Correct Answer
    lack of neutralization
  • overdriven stages
  • poor voltage regulation

Undesired positive feedback in an RF amplifier causes parasitic oscillations: the amplifier becomes an oscillator. Inter-electrode capacitance (e.g., plate-to-grid), coupling from output to input, stray inductance or capacitance can start up oscillations. Neutralization is the process of cancelling positive-feedback paths. To test a tube amplifier for parasitic oscillations, connect nothing to the input and output terminals, apply DC power, monitor grid and plate current while slowly varying the controls on the output tuning network; if grid current develops or plate current changes, oscillations are present.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What type of signal does a balanced modulator produce?

  • Full carrier
  • Single sideband, suppressed carrier
  • Correct Answer
    Double sideband, suppressed carrier
  • FM with balanced deviation

One method of producing SSB is a Balanced Modulator followed by a filter. The modulator takes in a fixed-frequency RF signal and mixes it with audio from the speech amplifier. The modulator is said to be balanced because the two original inputs are not present at the output: carrier suppression has taken place. Present, however, are a lower and upper sideband. A subsequent filter selects one of the sidebands to complete the creation of a single sideband suppressed-carrier signal. Note that there is no RF output when no audio is applied.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

How can a single-sideband phone signal be produced?

  • By using a loop modulator followed by a mixer
  • By using a reactance modulator followed by a mixer
  • Correct Answer
    By using a balanced modulator followed by a filter
  • By driving a product detector with a DSB signal

One method of producing SSB is a Balanced Modulator followed by a filter. The modulator takes in a fixed-frequency RF signal and mixes it with audio from the speech amplifier. The modulator is said to be balanced because the two original inputs are not present at the output: carrier suppression has taken place. Present, however, are a lower and upper sideband. A subsequent filter selects one of the sidebands to complete the creation of a single sideband suppressed-carrier signal. Note that there is no RF output when no audio is applied.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Carrier suppression in a single-sideband transmitter takes place in:

  • the frequency multiplier stage
  • Correct Answer
    the balanced modulator stage
  • the carrier decouple stage
  • the mechanical filter

One method of producing SSB is a Balanced Modulator followed by a filter. The modulator takes in a fixed-frequency RF signal and mixes it with audio from the speech amplifier. The modulator is said to be balanced because the two original inputs are not present at the output: carrier suppression has taken place. Present, however, are a lower and upper sideband. A subsequent filter selects one of the sidebands to complete the creation of a single sideband suppressed-carrier signal. Note that there is no RF output when no audio is applied.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Transmission with SSB, as compared to conventional AM transmission, results in:

  • a greater bandpass requirement in the receiver
  • 3 dB gain in the transmitter
  • Correct Answer
    6 dB gain in the transmitter and 3 dB gain in the receiver
  • 6 dB gain in the receiver

Under noisy conditions, SSB can bring up to a 9 dB improvement over an AM signal of the same peak power. In AM, the Peak Envelope Power present in one of the two sidebands equals one fourth the carrier power: e.g., a 100-watt AM transmitter only packs 25 watts PEP in each sideband. SSB concentrates all the available power in one sideband alone: a 4 to 1 improvement or 6 dB. Using half the bandwidth on SSB reception, permits taking in only half of the noise at the receiver, an additional 3 dB improvement.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

The peak power output of a single-sideband transmitter, when being tested by a two-tone generator is:

  • one-half of the RF peak output power of any of the tones
  • one-quarter of the RF peak output power of any of the tones
  • Correct Answer
    twice the RF power output of any of the tones
  • equal to the RF peak output power of any of the tones

A two-tone test permits verifying the linearity of an SSB transmitter. The test requires a generator producing two low-distortion non-harmonically related audio sine waves of equal amplitude. The frequencies must fall within the normal transmitter audio passband: e.g., 700 and 1900 Hz. A sample of the transmitter's output is observed on an oscilloscope while the tones are fed into the microphone input. Feeding an SSB transmitter with two equal-amplitude steady audio tones produces two equal-amplitude RF signals: total power is thus twice the power present in each RF signal.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What kind of input signal is used to test the amplitude linearity of a single-sideband phone transmitter while viewing the output on an oscilloscope?

  • An audio-frequency square wave
  • Normal speech
  • Correct Answer
    Two audio-frequency sine waves
  • An audio-frequency sine wave

A two-tone test permits verifying the linearity of an SSB transmitter. The test requires a generator producing two low-distortion non-harmonically related audio sine waves of equal amplitude. The frequencies must fall within the normal transmitter audio passband: e.g., 700 and 1900 Hz. A sample of the transmitter's output is observed on an oscilloscope while the tones are fed into the microphone input. Feeding an SSB transmitter with two equal-amplitude steady audio tones produces two equal-amplitude RF signals: total power is thus twice the power present in each RF signal.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

When testing the amplitude linearity of a single-sideband transmitter what audio tones are fed into the microphone input and on what kind of kind of instrument is the output observed?

  • Two harmonically related tones are fed in, and the output is observed on an oscilloscope
  • Two harmonically related tones are fed in, and the output is observed on a distortion analyzer
  • Two non-harmonically related tones are fed in, and the output is observed on a distortion analyzer
  • Correct Answer
    Two non-harmonically related tones are fed in, and the output is observed on an oscilloscope

A two-tone test permits verifying the linearity of an SSB transmitter. The test requires a generator producing two low-distortion non-harmonically related audio sine waves of equal amplitude. The frequencies must fall within the normal transmitter audio passband: e.g., 700 and 1900 Hz. A sample of the transmitter's output is observed on an oscilloscope while the tones are fed into the microphone input. Feeding an SSB transmitter with two equal-amplitude steady audio tones produces two equal-amplitude RF signals: total power is thus twice the power present in each RF signal.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What audio frequencies are used in a two-tone test of the linearity of a single-sideband phone transmitter?

  • Correct Answer
    Any two audio tones may be used, but they must be within the transmitter audio passband, and should not be harmonically related
  • 20 Hz and 20 kHz tones must be used
  • 1200 Hz and 2400 Hz tones must be used
  • Any two audio tones may be used, but they must be within the transmitter audio passband, and must be harmonically related

A two-tone test permits verifying the linearity of an SSB transmitter. The test requires a generator producing two low-distortion non-harmonically related audio sine waves of equal amplitude. The frequencies must fall within the normal transmitter audio passband: e.g., 700 and 1900 Hz. A sample of the transmitter's output is observed on an oscilloscope while the tones are fed into the microphone input. Feeding an SSB transmitter with two equal-amplitude steady audio tones produces two equal-amplitude RF signals: total power is thus twice the power present in each RF signal.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What measurement can be made of a single-sideband phone transmitter's amplifier by performing a two-tone test using an oscilloscope?

  • Correct Answer
    Its linearity
  • Its frequency deviation
  • Its percent of carrier phase shift
  • Its percent of frequency modulation

A two-tone test permits verifying the linearity of an SSB transmitter. The test requires a generator producing two low-distortion non-harmonically related audio sine waves of equal amplitude. The frequencies must fall within the normal transmitter audio passband: e.g., 700 and 1900 Hz. A sample of the transmitter's output is observed on an oscilloscope while the tones are fed into the microphone input. Feeding an SSB transmitter with two equal-amplitude steady audio tones produces two equal-amplitude RF signals: total power is thus twice the power present in each RF signal.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

How much is the carrier suppressed below peak output power in a single-sideband phone transmission?

  • At least 60 dB
  • Correct Answer
    At least 40 dB
  • No more than 20 dB
  • No more than 30 dB

"Most well-designed balanced modulators can provide between 30 and 50 dB of carrier suppression. ...The filter roll-off can be used to obtain an additional 20 dB of carrier suppression." (ARRL Handbook 1985)

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is meant by "flat topping" in a single-sideband phone transmission?

  • The transmitter's carrier is properly suppressed
  • Correct Answer
    Signal distortion caused by excessive drive
  • Signal distortion caused by insufficient collector current
  • The transmitter's automatic level control is properly adjusted

Flattening of the peaks is an extreme form of distortion where the output of the transmitter is incapable of reproducing the original pattern of the audio input on voice peaks. This is generally caused by excessive audio input to the transmitter: too much audio causes the amplifier stage to exceed its linear operation range. The purpose of the ALC (Automatic Level Control) is to prevent overdrive.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Maintaining the peak RF output of a SSB transmitter at a relatively constant level requires a circuit called the:

  • Correct Answer
    automatic level control (ALC)
  • automatic gain control (AGC)
  • automatic output control (AOC)
  • automatic volume control (AVC)

Automatic Level Control (ALC) serves to prevent overdriving an amplifier. The ALC circuit samples the envelope (peak) of the RF output to develop a DC control voltage used to control the gain of an earlier stage. AGC and AVC are receiver circuits.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Speech compression associated with SSB transmission implies:

  • a lower signal-to-noise ratio
  • circuit level instability
  • Correct Answer
    full amplification of low level signals and reducing or eliminating amplification of high level signals
  • full amplification of high level signals and reducing or eliminating signals amplification of low level

Audio compression maintains a high voice level despite variations in the voice signal incoming from a microphone. To produce a high average output without exceeding a certain peak value, low level signals need to be amplified while high level signals are passed along with little or no gain. [ compression is the automatic reduction of gain as the signal level increases beyond a pre-set level known as the threshold. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Which principle is not associated with analog signal processing?

  • Clipping
  • Correct Answer
    Frequency division
  • Compression
  • Bandwidth limiting

Key words: NOT ASSOCIATED WITH ANALOG. Compression, bandwidth limiting and clipping can all be performed as analog processes. Frequency division requires a numerical computation.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Which of the following is not a method used for peak limiting, in a signal processor?

  • AF clipping
  • Correct Answer
    Frequency clipping
  • RF clipping
  • Compression

The expression "peak limiting" entails limiting the amplitude. Compression, AF clipping and RF clipping are valid operations. There is no such thing as frequency clipping.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the undesirable result of AF clipping in a speech processor?

  • Reduction in peak amplitude
  • Correct Answer
    Increased harmonic distortion
  • Reduced average power
  • Increased average power

Audio frequency clipping abruptly stops voltage excursions at a certain level. This gives the audio a square wave appearance; square waves are rich in harmonics. AF clippers need to be followed by a low-pass filter to prevent harmonics from entering modulation stages. You may also eliminate the bad answers: "reduction in peak amplitude" is the object of clipping, "increased average power" is a result of clipping (softer passages are no longer dwarfed by the peaks), "increased average power" simply contradicts the previous answer.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Which description is not correct? You are planning to build a speech processor for your transceiver. Compared to AF clipping, RF clipping:

  • is more expensive to implement
  • is more difficult to implement
  • Correct Answer
    is easier to implement
  • has less distortion

Working at radio-frequencies is evidently more difficult and thus more expensive than dealing with audio frequencies. RF clipping is generally presumed to induce less distortion because any harmonics generated through clipping automatically end up outside the passband of subsequent filters. At audio frequencies, harmonics of the lower speech frequencies fall within the audio passband and can muddle the audio signal.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Automatic Level Control (ALC) is another name for:

  • AF clipping
  • Correct Answer
    RF compression
  • AF compression
  • RF clipping

Clipping places a hard limit on voltage swings. Compression is a reduction in gain when signal exceed a certain threshold. The ALC circuit samples the envelope (peak) of the RF output and produces a DC control voltage used to control the gain of an earlier stage when the output reaches a certain level.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In an FM phone signal having a maximum frequency deviation of 3000 Hz either side of the carrier frequency, what is the modulation index, when the modulating frequency is 1000 Hz?

  • 0.3
  • 3000
  • 1000
  • Correct Answer
    3

Deviation = the amount of frequency shift, at a given instant, from the centre carrier frequency (e.g., plus or minus 5 kHz). Modulation Index = the ratio of deviation to modulating frequency for a particular audio frequency (both being expressed in the same units): e.g., 3 kHz deviation with 1 kHz audio represents a Modulation Index of 3. Deviation Ratio = the ratio of maximum deviation to the maximum modulating frequency: e.g. maximum deviation of 5 kHz with a highest modulating frequency of 3 kHz is a Deviation Ratio of 1.66 .

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the modulation index of an FM phone transmitter producing an instantaneous carrier deviation of 6 kHz when modulated with a 2 kHz modulating frequency?

  • Correct Answer
    3
  • 0.333
  • 2000
  • 6000

Deviation = the amount of frequency shift, at a given instant, from the centre carrier frequency (e.g., plus or minus 5 kHz). Modulation Index = the ratio of deviation to modulating frequency for a particular audio frequency (both being expressed in the same units): e.g., 3 kHz deviation with 1 kHz audio represents a Modulation Index of 3. Deviation Ratio = the ratio of maximum deviation to the maximum modulating frequency: e.g. maximum deviation of 5 kHz with a highest modulating frequency of 3 kHz is a Deviation Ratio of 1.66 .

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the deviation ratio of an FM phone transmitter having a maximum frequency swing of plus or minus 5 kHz and accepting a maximum modulation rate of 3 kHz?

  • Correct Answer
    1.66
  • 60
  • 0.16
  • 0.6

Deviation = the amount of frequency shift, at a given instant, from the centre carrier frequency (e.g., plus or minus 5 kHz). Modulation Index = the ratio of deviation to modulating frequency for a particular audio frequency (both being expressed in the same units): e.g., 3 kHz deviation with 1 kHz audio represents a Modulation Index of 3. Deviation Ratio = the ratio of maximum deviation to the maximum modulating frequency: e.g. maximum deviation of 5 kHz with a highest modulating frequency of 3 kHz is a Deviation Ratio of 1.66 .

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the deviation ratio of an FM phone transmitter having a maximum frequency swing of plus or minus 7.5 kHz and accepting a maximum modulation rate of 3.5 kHz?

  • 0.47
  • 47
  • 0.214
  • Correct Answer
    2.14

Deviation = the amount of frequency shift, at a given instant, from the centre carrier frequency (e.g., plus or minus 5 kHz). Modulation Index = the ratio of deviation to modulating frequency for a particular audio frequency (both being expressed in the same units): e.g., 3 kHz deviation with 1 kHz audio represents a Modulation Index of 3. Deviation Ratio = the ratio of maximum deviation to the maximum modulating frequency: e.g. maximum deviation of 5 kHz with a highest modulating frequency of 3 kHz is a Deviation Ratio of 1.66 .

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

When the transmitter is not modulated, or the amplitude of the modulating signal is zero, the frequency of the carrier is called its:

  • modulating frequency
  • Correct Answer
    centre frequency
  • frequency deviation
  • frequency shift

Centre Frequency is the transmitter output frequency in the absence of modulation. Frequency deviation and frequency shift both are synonyms for the offset in carrier frequency caused by modulation at a given instant. Modulating frequency relates to the audio frequency used for modulation.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In an FM transmitter system, the amount of deviation from the centre frequency is determined solely by the:

  • amplitude and the frequency of the modulating frequency
  • modulating frequency and the amplitude of the centre frequency
  • Correct Answer
    amplitude of the modulating frequency
  • frequency of the modulating frequency

In Frequency Modulation, the amplitude of the modulation is translated into the importance of the deviation, the modulation frequency is reflected in the rhythm of the deviation.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Any FM wave with single-tone modulation has:

  • Correct Answer
    an infinite number of sideband frequencies
  • two sideband frequencies
  • four sideband frequencies
  • one sideband frequency

Unlike AM where a single modulating frequency creates only a pair of side frequencies (one on each side of the carrier), FM creates an infinite number of side frequency pairs; the Modulation Index influences the amplitude of the side frequencies through a mathematical relation known as a Bessel Function. The number of side frequencies with significant amplitude determines the required bandwidth. For certain Modulation Index values, there is zero energy at the centre frequency; the energy is then totally found in the side frequencies.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Some types of deviation meters work on the principle of:

  • Correct Answer
    a carrier null and multiplying the modulation frequency by the modulation index
  • detecting the frequencies in the sidebands
  • the amplitude of power in the sidebands
  • a carrier peak and dividing by the modulation index

Certain Modulation Index values cause nulls at the centre carrier frequency: e.g., the Bessel function returns zero for the carrier component at Modulation Indices of 2.4048, 5.5201 or 8.6537 . Detecting a carrier null permits determining deviation as Modulation Index times modulating frequency. For example, with a tone of 905 hertz and deviation set at 4996 hertz (nearly 5 kHz), a null in the carrier will be observed because 4996 Hz deviation for a tone of 905 Hz is a Modulation Index of 5.52 . An all-mode receiver with a sharp filter permits observing the carrier component. The procedure could be used to set a transmitter or calibrate a home-made deviation meter.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

When using some deviation meters, it is important to know:

  • pass-band of the IF filter
  • Correct Answer
    modulating frequency and the modulation index
  • modulation index
  • modulating frequency

Certain Modulation Index values cause nulls at the centre carrier frequency: e.g., the Bessel function returns zero for the carrier component at Modulation Indices of 2.4048, 5.5201 or 8.6537 . Detecting a carrier null permits determining deviation as Modulation Index times modulating frequency. For example, with a tone of 905 hertz and deviation set at 4996 hertz (nearly 5 kHz), a null in the carrier will be observed because 4996 Hz deviation for a tone of 905 Hz is a Modulation Index of 5.52 . An all-mode receiver with a sharp filter permits observing the carrier component. The procedure could be used to set a transmitter or calibrate a home-made deviation meter.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the significant bandwidth of an FM-phone transmission having a +/- 5-kHz deviation and a 3-kHz modulating frequency?

  • 8 kHz
  • 5 kHz
  • 3 kHz
  • Correct Answer
    16 kHz

Carson's Rule permits estimating the bandwidth of an FM signal: bandwidth equals twice the sum of deviation + modulating frequency, in this example, 5 + 3 = 8, twice 8 = 16. [ Mathematician and engineer John R. Carson (1887-1940) had predicted the approximate bandwidth of an FM signal circa 1922. ]

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What is the frequency deviation for a 12.21-MHz reactance-modulated oscillator in a +/- 5-kHz deviation, 146.52-MHz FM-phone transmitter?

  • +/- 12 kHz
  • +/- 5 kHz
  • +/- 41.67 Hz
  • Correct Answer
    +/- 416.7 Hz

In this example, the frequency multiplication ratio between oscillator and output is 12 ( 146.52 divided by 12.21 = 12 ). Hence, the oscillator needs only be shifted by 416.7 Hz, i.e., 5000 Hz divided by 12.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What type of circuit varies the tuning of an amplifier tank circuit to produce FM signals?

  • Correct Answer
    A phase modulator
  • A balanced modulator
  • A double balanced mixer
  • An audio modulator

Two methods exist to produce Frequency Modulation. The Direct Method supposes forcing deviation directly on the oscillator; deviation is then multiplied along with the oscillator frequency up to the operating frequency. Phase Modulation is an indirect method whereby the phase of the signal is affected (i.e., retarding/advancing) in step with the modulation by varying a reactance on a stage other than the oscillator.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

What audio shaping network is added at an FM transmitter to attenuate the lower audio frequencies?

  • Correct Answer
    A pre-emphasis network
  • An audio prescaler
  • A heterodyne suppressor
  • A de-emphasis network

With direct FM, deviation is independent of modulating frequency, actual deviation is determined solely by the modulating amplitude. With Phase Modulation, deviation depends on the amount of phase shift and its rapidity, increasing modulating frequency results in proportionally more deviation even if amplitude is held constant. Because commercial standards were based on Phase Modulation, an FM transmitter requires an artificial boost in high frequency response so that PM and FM sound the same at the receiver. A pre-emphasis network tailors the frequency response in the FM transmitter. De-emphasis is employed in the receiver to restore a flat audio response.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

The characteristic difference between a phase modulator and a frequency modulator is:

  • the centre frequency
  • de-emphasis
  • frequency inversion
  • Correct Answer
    pre-emphasis

With direct FM, deviation is independent of modulating frequency, actual deviation is determined solely by the modulating amplitude. With Phase Modulation, deviation depends on the amount of phase shift and its rapidity, increasing modulating frequency results in proportionally more deviation even if amplitude is held constant. Because commercial standards were based on Phase Modulation, an FM transmitter requires an artificial boost in high frequency response so that PM and FM sound the same at the receiver. A pre-emphasis network tailors the frequency response in the FM transmitter. De-emphasis is employed in the receiver to restore a flat audio response.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

In most modern FM transmitters, to produce a better sound, a compressor and a clipper are placed:

  • Correct Answer
    between the audio amplifier and the modulator
  • between the multiplier and the PA
  • between the modulator and the oscillator
  • in the microphone circuit, before the audio amplifier

In this context, compression and clipping are AUDIO processes aimed at maintaining high average deviation without exceeding a given peak value. Two answers can be readily scratched as they pertain to radiofrequency (RF) paths. The microphone circuit is not suitable as the audio level at that point is too low for a simple clipper.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Three important parameters to be verified in an FM transmitter are:

  • distortion, bandwidth and sideband power
  • modulation, pre-emphasis and carrier suppression
  • frequency stability, de-emphasis and linearity
  • Correct Answer
    power, frequency deviation and frequency stability

Stability is paramount in all transmitters, frequency deviation ultimately determines bandwidth while linearity (absence of distortion) minimizes out-of-channel emissions. Carrier Suppression is a concern with SSB, pre-emphasis (FM transmitter) and de-emphasis (FM receiver) are simple resistor-capacitor networks.

Original copyright; explanations transcribed with permission from Francois VE2AAY, author of the ExHAMiner exam simulator. Do not copy without his permission.

Tags: none

Go to L07 Go to L16