Login or Register for FREE!
Subelement T4

AMATEUR RADIO PRACTICES

Section T4B

Operating controls: frequency tuning, use of filters, squelch function, AGC, memory channels, noise blanker, microphone gain, receiver incremental tuning (RIT), bandwidth selection, digital transceiver configuration

What is the effect of excessive microphone gain on SSB transmissions?

  • Frequency instability
  • Correct Answer
    Distorted transmitted audio
  • Increased SWR
  • All these choices are correct

Some microphones have an adjustable gain control. Some radios have an internal gain control to trim the audio gain of the microphone. If the gain is set too high it can exceed the range that circuitry can handle and will cause the audio signal to be distorted. Distortion might be fine for your old tube type guitar amplifier but it will render your signal quality as unreadable.

Last edited by v-man. Register to edit

Tags: troubleshooting noise and interference arrl chapter 5 arrl module 11

Which of the following can be used to enter a transceiver’s operating frequency?

  • Correct Answer
    The keypad or VFO knob
  • The CTCSS or DTMF encoder
  • The Automatic Frequency Control
  • All these choices are correct

VFO means Variable Frequency Oscillator; back in the time of crystals you often had to "program" a radio by changing crystals in the radio and then using a knob to select them. Modern radios are much easier to set up; most of them you can simply type in the frequency you want on the keypad. Some lack a keypad, but have a "tuning knob", or "VFO knob". Many have both options, since each has its uses.

CTCSS refers to a subaudible tone (also called a PL tone or a privacy code by FRS manufacturers) and DTMF tones are the tones generated when you press a key on your telephone; neither has anything to do with entering the operating frequency. Automatic Frequency Control keeps the receiver tuned to an incoming signal - thus it is not a method of entering an operating frequency.

Last edited by camplate. Register to edit

Tags: radio operation arrl chapter 5 arrl module 11

How is squelch adjusted so that a weak FM signal can be heard?

  • Correct Answer
    Set the squelch threshold so that receiver output audio is on all the time
  • Turn up the audio level until it overcomes the squelch threshold
  • Turn on the anti-squelch function
  • Enable squelch enhancement

The squelch option on a radio is meant to suppress or mute sound when transmissions are not being received. This works by muting the receiver until a received signal strength exceeds the squelch setting. If the squelch is all the way down (i.e. receiver is never muted), then received transmissions of any strength will be heard on your transceiver, including weak FM signals with low output power.

Last edited by amazon10x. Register to edit

Tags: none

What is a way to enable quick access to a favorite frequency or channel on your transceiver?

  • Enable the frequency offset
  • Correct Answer
    Store it in a memory channel
  • Enable the VOX
  • Use the scan mode to select the desired frequency

The ability of most radios to store/program and recall our favorite frequencies gives us quick access to them. These memories can be programmed with more than just the frequency that is needed. For example to reach a repeater we need the correct frequency, input offset frequency and CTCSS tone.

The distractor answers may sound right but remember the key words here are frequency, which is found in the question and correct answer, quick and memory. A good memory is important to get the right frequency recalled quickly.

Last edited by javadog. Register to edit

Tags: radio operation arrl chapter 5 arrl module 11

What does the scanning function of an FM transceiver do?

  • Checks incoming signal deviation
  • Prevents interference to nearby repeaters
  • Correct Answer
    Tunes through a range of frequencies to check for activity
  • Checks for messages left on a digital bulletin board

A scanning function is useful for scanning through a range of frequencies to check for activity. None of the other options have anything to do with scanning.

The scanning feature on a radio will rapidly switch receive frequencies automatically, pausing on each frequency for only a fraction of a second to see if a carrier signal is present indicating that someone is actively transmitting on that frequency. If no carrier is present on a frequency it continues to the next one.

If a carrier is present on a frequency then the action taken is usually user-configurable. Scanning features can typically be configured to stop on the frequency until manually told to continue, to stop for only a few seconds, or stop for as long as the carrier signal remains then continue. More sophisticated scanning features may have more advanced options. Scanners can often be configured to scan a list of specific frequencies (such as repeaters) rather than an incremental range.

As you can imagine, this can be very useful for finding other operators to communicate with when you have no idea what frequency they might be transmitting on.

Last edited by rjstone. Register to edit

Tags: arrl chapter 6 arrl module 15

Which of the following controls could be used if the voice pitch of a single-sideband signal returning to your CQ call seems too high or low?

  • The AGC or limiter
  • The bandwidth selection
  • The tone squelch
  • Correct Answer
    The RIT or Clarifier

RIT stands for Receiver Incremental Tuning. It is a fine tuning control to adjust the receiver frequency without adjusting the transmitter frequency.

While SSB is a very efficient transmission mode, everyone ends up sounding somewhat like Donald Duck. This is due to the fact that the transmit carrier frequency is missing. RIT Stands for Receiver Incremental Tuning which in effect, recreates the signal's missing carrier transmit frequency. When the RIT adjustment is misadjusted, the result can be a voice which is too high or too low sounding. Adjust the RIT until the voice sounds correct. Keep in mind some people have naturally higher voices than others. The direction you adjust the RIT will be in opposite directions for upper sideband (USB) vs. lower sideband (LSB), SSB signals.

Last edited by brianaburk. Register to edit

Tags: radio operation hf arrl chapter 5 arrl module 11

What does a DMR “code plug” contain?

  • Your call sign in CW for automatic identification
  • Correct Answer
    Access information for repeaters and talkgroups
  • The codec for digitizing audio
  • The DMR software version

A "code plug" contains the programming information for a DMR-capable radio. This programming information contains programmed channels, frequencies, and tones required to communicate through a repeater and into talkgroups. A code plug is generally unique to a specific model of radio.

Last edited by alekmurray. Register to edit

Tags: none

What is the advantage of having multiple receive bandwidth choices on a multimode transceiver?

  • Permits monitoring several modes at once by selecting a separate filter for each mode
  • Correct Answer
    Permits noise or interference reduction by selecting a bandwidth matching the mode
  • Increases the number of frequencies that can be stored in memory
  • Increases the amount of offset between receive and transmit frequencies

What is the advantage of having multiple receive bandwidth choices on a multimode transceiver?

Different modes use different amounts of bandwidth; if you are using a narrow receive bandwidth and the mode is wide FM, you will only "hear" a portion of the signal. On the other hand if you're using a wide FM receive bandwidth and the mode is narrow FM, you may not be able to make out the signal at all and there could be interference from other stations on nearby frequencies. The best signal will be experienced when the receiver is expecting the same amount of bandwidth that the transmitter is transmitting.

Last edited by liaellentron. Register to edit

Tags: radio operation bandwidth noise and interference hf arrl chapter 5 arrl module 11

How is a specific group of stations selected on a digital voice transceiver?

  • By retrieving the frequencies from transceiver memory
  • By enabling the group’s CTCSS tone
  • Correct Answer
    By entering the group’s identification code
  • By activating automatic identification

There is probably some room for argument on this question, since it tries to be generic to all digital voice modes -- but keep in mind it's talking about the most common case.

The key here is "digital voice", so selecting stations is not usually going to be just a question of checking frequencies. Similarly since it's digital you don't use a CTCSS tone -- those are used for analog conversations. Automatic identification is a real and a cool thing with digital voice, but it is not going to affect what stations you are talking to!

Digital Voice indicates a mode where the audio (voice) is encoded into a digital format and transmitted using some kind of digital modulation -- think old-school modems, though it's a bit more advanced than that. If you listen with an analog transceiver you'll hear "computer tones" that you can't understand. Because it's digital the transmitter can encode a lot of extra information with the signal, including things like a group code, your call sign, etc.

Common practice for digital voice operation is to have some kind of group identification code which is entered into the transmitter and sent with the signal; whatever is listening on the other side (usually a repeater or hotspot) then looks at that and decides where to send the signal.

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 6 arrl module 15

Which of the following receiver filter bandwidths provides the best signal-to-noise ratio for SSB reception?

  • 500 Hz
  • 1000 Hz
  • Correct Answer
    2400 Hz
  • 5000 Hz

SSB is Single Sideband From HamUniverse.com

The information contained in the average human voice needed to understand the voice is contained within about the first 3000hz of the human hearing range. Frequencies of the human voice beyond this range are not needed for communication purposes and are filtered out in the modulation process. So the average bandwidth of a SSB signal is about 3000hz wide with all of the voice characteristics needed within that range to be understandable.

Hearing Frequency Range Starting with the main frequency range, it is the frequency range of human hearing, which is responsible for the perception of speech. It covers the frequencies from 300 to 3000 Hz. The range of frequencies in which the intelligibility and the recognition of the tuning characteristics are concerned is between the above mentioned frequency. This frequency range is used for voice communication in telephony and is the range the human ear is the most sensitive. Because of this, a 2400Hz filter will generally leave enough of the voice characteristics to be understandable but filter out much of the noise. (See also http://www.seaindia.in/blog/human-voice-frequency-range/)

Last edited by the_lab_cat. Register to edit

Tags: filters ssb noise and interference hf arrl chapter 5 arrl module 11

Which of the following must be programmed into a D-STAR digital transceiver before transmitting?

  • Correct Answer
    Your call sign
  • Your output power
  • The codec type being used
  • All these choices are correct

D-Star is a digital protocol and encodes your call sign into every transmission, which technically means that voice identification is not needed. Because of this you must program the call sign before transmitting because otherwise you're transmitting without identifying.

That is clear to most people, but many get thrown off thinking that all of the answers may be correct, so let's look at the distractors:

  • D-Star always uses the same codec, it can't be changed -- just that is enough to show that it can't be "all these choices". The codec is the component (software or hardware) which encodes your analog voice audio into digital data for transmission.
  • The output power is something you may want to set, but it's not something you must set -- any output power that a d-star capable radio can put out will be legal to use.

Last edited by kd7bbc. Register to edit

Tags: none

What is the result of tuning an FM receiver above or below a signal’s frequency?

  • Change in audio pitch
  • Sideband inversion
  • Generation of a heterodyne tone
  • Correct Answer
    Distortion of the signal’s audio

If you've ever used a manually tuned FM radio receiver (e.g. in a vehicle) you've experienced this where as you tune up the signal becomes more clear the closer to the exact frequency you get. Other types of modulation give you a change in audio pitch (such as AM or SSB) but with FM it just affects how much of the full signal you receive -- the more you receive the more clear the signal is.

Last edited by kd7bbc. Register to edit

Tags: none

Go to T4A Go to T5A