Login or Register for FREE!
Subelement G3

RADIO WAVE PROPAGATION

Section G3C

Ionospheric regions; critical angle and frequency; HF scatter; near vertical incidence skywave (NVIS)

Which ionospheric region is closest to the surface of Earth?

  • Correct Answer
    The D region
  • The E region
  • The F1 region
  • The F2 region

The layers of the atmosphere are in alphabetical order; the D, E, and F layers are considered the ionosphere and the D layer (at a height of 30 to 60 miles) is the region closest to the surface of the earth.

The ionosphere is the portion of the atmosphere responsible for Skywave Propagation (bouncing signals "off of the sky" to come back down long distances away), which makes it of particular interest to Amateur Radio operators.

For more info see Wikipedia: D region

To remember this you may want to remember D for Down.

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 8 arrl module 34

What is meant by the term “critical frequency” at a given incidence angle?

  • Correct Answer
    The highest frequency which is refracted back to Earth
  • The lowest frequency which is refracted back to Earth
  • The frequency at which the signal-to-noise ratio approaches unity
  • The frequency at which the signal-to-noise ratio is 6 dB

Each HF frequency is affected differently by the ionosphere at different times of day, season and angle it strikes the ionosphere. The maximum frequency that will be refracted back to earth, and not just continue into space, at a given time is called the "critical frequency".

Last edited by way10c. Register to edit

Tags: none

Why is skip propagation via the F2 region longer than that via the other ionospheric regions?

  • Because it is the densest
  • Because of the Doppler effect
  • Correct Answer
    Because it is the highest
  • Because of temperature inversions

(C). The F2 region appears when the highest layer of the ionosphere (the F region) becomes strongly ionized. As the ionization increases, the F layer splits into the lower F1 region and the higher F2 region. Because it is the highest ionospheric region, long distances may be reached in one bend or "hop" of the signal (up to about 2,500 miles!).

This is why the F2 region is mainly responsible for the longest distance radio wave propagation.

For more info see Wikipedia: F2 region

Last edited by qubit. Register to edit

Tags: arrl chapter 8 arrl module 34

What does the term “critical angle” mean, as applied to radio wave propagation?

  • The long path azimuth of a distant station
  • The short path azimuth of a distant station
  • The lowest takeoff angle that will return a radio wave to Earth under specific ionospheric conditions
  • Correct Answer
    The highest takeoff angle that will return a radio wave to Earth under specific ionospheric conditions

Silly hint: Your health is critical with high blood pressure.

In radio wave propagation, the term critical angle refers to the highest takeoff angle that will return a radio wave to the Earth under specific ionospheric conditions. If the angle of the signal leaving your antenna is too low, it may not reach the ionosphere, or if parallel to the earth, not even make it around the curvature of the earth and be lost. If the angle is too great the signal may go straight through the atmosphere and be lost into space. The critical angle, like the critical frequency levels of MUF and LUF are dependent on the conditions of the ionosphere, as the height of layers change with ionization levels, and the angle needed to reach those levels will change with those factors.

Last edited by bsolov. Register to edit

Tags: arrl chapter 8 arrl module 34

Why is long-distance communication on the 40-, 60-, 80-, and 160-meter bands more difficult during the day?

  • The F region absorbs signals at these frequencies during daylight hours
  • The F region is unstable during daylight hours
  • Correct Answer
    The D region absorbs signals at these frequencies during daylight hours
  • The E region is unstable during daylight hours

HF frequencies such as the 40, 60, 80 and 160 meter bands are harder to use for long distance communication during the day. The same factors that make the upper E and F layers great for the higher VHF frequencies make the lower D layer more "absorbant" of HF wave signals. The lower HF signals are attenuated or absorbed and so do not pass through for bending at higher ionospheric levels. Ionization is higher during daylight hours, and so the D layer absorbs these frequencies much more during daylight hours. This makes the band much more useful for nighttime use than during the day.

Remember "D" for Daylight, Dull, Diminished. For more info: see Wikipedia

Last edited by po_supe. Register to edit

Tags: arrl chapter 8 arrl module 34

What is a characteristic of HF scatter?

  • Phone signals have high intelligibility
  • Correct Answer
    Signals have a fluttering sound
  • There are very large, sudden swings in signal strength
  • Scatter propagation occurs only at night

HF scatter signals often sound distorted because the energy is scattered into the skip zone through several different radio wave paths. When this happens, the original signal is Split or Scattered and will be de-fragmented and may sound distorted at the receiver.

Last edited by ldwyze. Register to edit

Tags: arrl chapter 8 arrl module 36

What makes HF scatter signals often sound distorted?

  • The ionospheric region involved is unstable
  • Ground waves are absorbing much of the signal
  • The E region is not present
  • Correct Answer
    Energy is scattered into the skip zone through several different paths

HF scatter signals often sound distorted because the energy is scattered into the skip zone through several different radio wave paths.


Note:
A signal which is properly adjusted for angle and frequency is like tossing a clump of clay into the air: it makes a nice arc and comes back to earth at one spot, landing with a nice "thunk".

A signal which is scattered into the skip zone is like tossing up that same lump of clay into the air, but this time it hits the leaves of an overhanging tree which breaks up the clump. Some parts gets stuck in the tree, and the parts that do come down land in a wider area, making lots of smaller "scattered" sounds.

Silly, but easy, tip: the word "scatter" is used in the answer.

Last edited by grfd711. Register to edit

Tags: arrl chapter 8 arrl module 36

Why are HF scatter signals in the skip zone usually weak?

  • Correct Answer
    Only a small part of the signal energy is scattered into the skip zone
  • Signals are scattered from the magnetosphere, which is not a good reflector
  • Propagation is via ground waves, which absorb most of the signal energy
  • Propagation is via ducts in the F region, which absorb most of the energy

An HF signal in the skip zone gets broken up by the ionospheric conditions, where only a small part of the signal energy is scattered into the skip zone. The signal that does get back to the receiving station arrives in "little bits" at slightly different angles, and so produces a weak and wavering sound.

Hint: 'skip zone' in both question and answer.

Last edited by comdijital. Register to edit

Tags: arrl chapter 8 arrl module 36

What type of propagation allows signals to be heard in the transmitting station’s skip zone?

  • Faraday rotation
  • Correct Answer
    Scatter
  • Chordal hop
  • Short-path

With radio signals you have ground wave, meaning your signal goes between point a-b directly. Then you have sky waves, where your signal hits the ionosphere and bounces back down to earth possibly hundreds of miles away. What happens if you have a station you want to talk to in between the reach of your ground wave and sky wave? Those are the stations in your "skip zone." The best way to reach them is by scatter, meaning your signal will scatter off the ionosphere and possibly hit your station in the skip zone. NVIS or Near Vertical Incidence Skywave is scatter propogation.

Silly Hint: Imagine yourself "scattering" papers about trying to figure out why the signal is heard in the skip zone.

The shortest answer is the correct answer.

Last edited by 116028133357781257840. Register to edit

Tags: arrl chapter 8 arrl module 36

What is near vertical incidence skywave (NVIS) propagation?

  • Propagation near the MUF
  • Correct Answer
    Short distance MF or HF propagation at high elevation angles
  • Long path HF propagation at sunrise and sunset
  • Double hop propagation near the LUF

Near Vertical Incidence Sky-wave (NVIS) propagation as the name indicates uses signals which are sent out at very high angles, yet below the critical angle, or these signals would go right out into space! Because these signals take a shorter path through the ionospheric layers, they often have less absorption, attenuation or distortion of the signal. This method can be great for high quality short distance HF propagation using these high elevation angles, especially where there are interferences in the way of direct ground-wave propagation.

Hint: Near vertical implies high elevation angle.

For more info see Wikipedia: Near Vertical Incidence Sky-wave (NVIS)

Oversimplification: basically, instead of an antenna that radiates parallel to the ground, like a mag mount on your car or a Yagi pointed across town, you tip it over 90 degrees so you're sending RF at the sky (Yagi pointed at zenith in "Christmas Tree Mode"). These are also known as "cloud warmers."

Last edited by kd7bbc. Register to edit

Tags: arrl chapter 8 arrl module 36

Which ionospheric region is the most absorbent of signals below 10 MHz during daylight hours?

  • The F2 region
  • The F1 region
  • The E region
  • Correct Answer
    The D region

The daylight ionization that makes the upper ionospheric regions great for VHF sky-wave propagation works against HF frequencies below 10 MHz. During the daytime the D layer absorbs these signals. Think of the D layer as a "Daylight Dud". This layer becomes much more usable after dark, when ionization of the band decreases its "absorbent" character.

For more info see Wikipedia: D region

Hint: During Daylight D region

Last edited by dosewallips. Register to edit

Tags: arrl chapter 8 arrl module 34

Go to G3B Go to G4A